Upgrade from Fedora 19 to 20 using fedup
The recommended upgrade method for Fedora is to use the fedup tool. Below is my experience in following the fedup procedure to upgrade from Fedora 19 to 20. The upgrade was done over the Internet ("network upgrade") instead of from a local DVD media.
- Back up all important data in the system.
- Verify that the hard disk has sufficient disk space.
Fedup first downloads the version 20 packages while the system is still running version 19. Therefore, the hard drive must have enough disk space to hold packages of both versions during the upgrade process. For my system, storing the version 20 packages requires about 2 GB.
- Perform a full system update under Fedora 19, and reboot to ensure that the system has the latest kernel changes.
$ sudo yum update
$ sudo reboot - Install fedup client.
The fedup client downloads over the Internet the boot image required to run the upgrade as well as the packages to be upgraded. It sets up the system to run the upgrade at the next boot.
$ sudo yum install fedup - Run fedup client.
$ sudo fedup --network 20The above command downloads over the Internet (from the Fedora mirror system) all needed packages to upgrade to Fedora 20. It took almost an hour for my system to download everything. You should always verify that the install was successful by checking the fedup log file, /var/log/fedup.log.
My first upgrade attempt appeared stalled towards the end of the download. So, I terminated the program with a Control-C. The fedup log file revealed a problem with downloading gnupg.
[ 4130.971] (II) fedup.cli:start_meter() download gnupg-1.4.18-1.fc20.i686.rpm
[ 4131.107] (II) fedup.yum:log_grab_failure() http://www.muug.mb.ca/pub/fedora/linux/updates/20/i386/gnupg-1.4.18-1.fc20.i686.rpm: [Errno 14] HTTP Error 416 - Requested Range Not SatisfiableI reran the command, and it went further than before but still failed with the error message Downloading failed: Didn't install any keys.
The log file revealed that the offending key was RPM-GPG-KEY-rpmfusion-nonfree-fedora-20.
[ 122.225] (--) fedup.yum:_retrievePublicKey() Retrieving key from file:///etc/pki/rpm-gpg/RPM-GPG-KEY-rpmfusion-nonfree-fedora-20
[ 122.266] (II) fedup.yum:_GPGKeyCheck() repo 'rpmfusion-nonfree' wants to import key /etc/pki/rpm-gpg/RPM-GPG-KEY-rpmfusion-nonfree-fedora-20
[ 122.267] (II) fedup.yum:check_keyfile() checking keyfile /etc/pki/rpm-gpg/RPM-GPG-KEY-rpmfusion-nonfree-fedora-20
[ 122.268] (DD) fedup.yum:check_keyfile() keyfile owned by package rpmfusion-nonfree-release-0:19-1
[ 122.271] (DD) fedup.yum:check_keyfile() package was signed with key cd30c86b
[ 122.272] (II) fedup.yum:check_keyfile() REJECTED: key cd30c86b is not trusted by rpm
[ 122.273] (II) fedup.yum:_GPGKeyCheck() no automatic trust for key %s
[ 122.273] (II) fedup:message() Downloading failed: Didn't install any keys
[ 122.274] (DD) fedup:To solve the key problem, I manually imported the key using the following command:
$ sudo rpmkeys --import /etc/pki/rpm-gpg/RPM-GPG-KEY-rpmfusion-nonfree-fedora-20Then, I ran the fedup command for the third time.
$ fedup --network 20
setting up repos...
No upgrade available for the following repos: fedora-chromium-stable
getting boot images...
.treeinfo.signed | 2.1 kB 00:00
setting up update...
finding updates 100% [=========================================================]
verify local files 100% [======================================================]
testing upgrade transaction
rpm transaction 100% [=========================================================]
rpm install 100% [=============================================================]
setting up system for upgrade
Finished. Reboot to start upgrade.
Packages without updates:
....
NOTE: Some repos could not be contacted: fedora-chromium-stable
If you start the upgrade now, packages from these repos will not be installed.The command completed with an informational message No upgrade available for the following repos: fedora-chromium-stable. The cause of the message is that Fedora 20 does not include Chromium in its official repository. I decided to ignore the message, and continued with the upgrade. As a result, Chromium will not be automatically upgraded. However, after the upgrade is finished, I can manually upgrade Chromium from an unofficial repository or install Google Chrome instead.
- Reboot the system.
$ sudo rebootNote that a new entry, System Upgrade, is added to the GRUB menu. This is the default entry, and will be automatically selected. The actual upgrade took about 1 hour for my system.
After the upgrade is complete, the system automatically reboots into Fedora 20.
- Login.
Now that Fedora 20 is running, login and run the following command to display the version information.
$ lsb_release -a
LSB Version: :core-4.1-ia32:core-4.1-noarch
Distributor ID: Fedora
Description: Fedora release 20 (Heisenbug)
Release: 20
Codename: Heisenbug - Install Chrome.
Instead of upgrading Chromium from an unofficial Fedora repository, I decided to switch to Chrome. Chrome is the free Google browser that is derived from the upstream Chromium project.
To install Chrome:
- Browse to the Google Chrome download site.
- Select to download the appropriate 32 or 64-bit Fedora rpm.
- Install the rpm
I first used the rpm command to install the package. It failed because of a dependency problem.
$ sudo rpm -i google-chrome-stable_current_i386.rpm
warning: google-chrome-stable_current_i386.rpm: Header V4 DSA/SHA1 Signature, key ID 7fac5991: NOKEY
error: Failed dependencies:
lsb >= 4.0 is needed by google-chrome-stable-37.0.2062.120-1.i386To resolve the dependency automatically, I used the yum command as follows:
$ sudo yum localinstall google-chrome-stable_current_i386.rpm
What was your experience in upgrading Fedora? Let us know by entering a comment.