NEW PRODUCTS – Pimoroni HyperPixel 4.0 Squares – Capacitive Touch + Non-Touch
NEW PRODUCTS – Pimoroni HyperPixel 4.0 Squares – Capacitive Touch + Non-Touch
We’ve got two blisteringly high-res displays for Raspberry Pi! First up, the Non-Touch Square!
Pimoroni HyperPixel 4.0 Square – Hi-Res Display for Raspberry Pi – Non-Touch – PIM475
It’s hip to be square with the Pimoroni’s HyperPixel 4.0 Square Display for Raspberry Pi computers. This display has all the great features of their standard HyperPixel 4.0—a crisp, brilliant IPS display and high-speed DPI interface—it’s just more square!
This square version of HyperPixel 4.0 is great for custom interfaces and control panels, and works really well for Pico-8 games. Everything is pre-soldered and ready to go, just pop it onto your Pi, run the installer, and away you go!
We also have a more expensive version with capacitive touch
Features:
- High-speed DPI interface
- 4.0″ IPS (wide viewing angle, 160°) display (72x72mm)
- 720×720 pixels (~254 PPI)
- 18-bit color (262,144 colors)
- 60 FPS frame rate
- 40-pin female header included to boost height for Pi B+, 2, 3, 3B+
- Standoffs included to securely attach to your Pi
- Compatible with all 40-pin header Raspberry Pi models – even a Pi Zero (it’ll overhang a bit though)
- One-line installer
HyperPixel 4.0 Square uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 254 pixels per inch (720×720 picrld) on its 4.0″ display. The display can show 18-bits of color (262,144 colors).
Please note: when installing HyperPixel 4.0 Square onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel.
It’ll work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you’re using it with a larger Pi then use the extra 40-pin header that’s included to boost it up to the required height. If you’re using a Pi Zero or Pi Zero W then just pop it straight onto the GPIO.
The included standoff kit allows you to mount your HyperPixel 4.0 Square safely and securely to your Pi. Just screw them into the posts on the underside of the HyperPixel 4.0 Square PCB and then secure with screws through the mounting holes on your Pi.
Now for the Capacitive Touch display!
Pimoroni HyperPixel 4.0 Square – Touch Display for Raspberry Pi – Capacitive Touch – PIM470
It’s hip to be square with the Pimoroni’s HyperPixel 4.0 Square Display with Capacitive Touch for Raspberry Pi computers. This display has all the great features of their standard HyperPixel 4.0—a crisp, brilliant IPS display, capacitive touchscreen, and high-speed DPI interface—it’s just more square!
This square version of HyperPixel 4.0 is great for custom interfaces and control panels, and works really well for Pico-8 games. Everything is pre-soldered and ready to go, just pop it onto your Pi, run the installer, and away you go!
We also have a less expensive version without capacitive touch
Features:
- High-speed DPI interface
- 4.0″ IPS (wide viewing angle, 160°) display (72x72mm)
- 720×720 pixels (~254 PPI)
- 18-bit color (262,144 colors)
- 60 FPS frame rate
- Capacitive touchscreen
- 40-pin female header included to boost height for Pi B+, 2, 3, 3B+
- Standoffs included to securely attach to your Pi
- Compatible with all 40-pin header Raspberry Pi models
- One-line installer
HyperPixel 4.0 Square uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 254 pixels per inch (720x720px) on its 4.0″ display. The display can show 18-bits of color (262,144 colors).
The touchscreen variant is capacitive touch, that’s more sensitive and responsive to touch than a resistive touch display, and it’s capable of multi-touch!
Please note: when installing HyperPixel 4.0 Square onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel.
It’ll work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you’re using it with a larger Pi then use the extra 40-pin header that’s included to boost it up to the required height. If you’re using a Pi Zero or Pi Zero W then just pop it straight onto the GPIO.
The included standoff kit allows you to mount your HyperPixel 4.0 Square safely and securely to your Pi. Just screw them into the posts on the underside of the HyperPixel 4.0 Square PCB and then secure with screws through the mounting holes on your Pi.
from Adafruit Industries – Makers, hackers, artists, designers and engineers! https://ift.tt/2S4n4jg
via IFTTT